STP

StaceyStacey Member Posts: 10
edited April 6 in Other Reckon Products
STP submissions still in pending mode. I rang Reckon and they advised to contact ATO. ATO says its a Reckon problem! Help, what do i do? Pending from August 2018 and 2 submissions in Oct 2019.

Comments

  • RavRav Administrator Posts: 10,925 Administrator
    edited March 2019
    This is a similar situation to the case in your other thread. If you've made successful STP lodgements AFTER these pay events then your figures are up to date as STP is reported on a YTD basis.
  • StaceyStacey Member Posts: 10
    edited April 2019
    Thanks Rav! I have had successful submissions since but its disconcerting looking at this "Pending" status. Will just sit on this again and hopefully it will right itself.
  • Pamela BurnsPamela Burns Member Posts: 1
    edited April 2019
    I also had most of my lodgements sitting on "Pending" I found that when i went into the "detail" option the status changed to Success when i went back to the lodgement page.
  • JocelynJocelyn Member Posts: 19
    edited June 2019
    I have finally managed to get my last 6 payruns through as successful, all the rest are either errors or pending.  what happens to all the previous weeks - I have 85 other submissions sitting there? and what happens for employees that have resigned earlier in the financial year?  Are their figures up to date too?

  • RavRav Administrator Posts: 10,925 Administrator
    edited April 2019
    Hi Jocelyn,
    Pay events that are in an error state will not change. If you've corrected the error and your current pay events have been successful as you've mentioned then your YTD figures are up to date.

    Check out this article for more info on commencing STP mid-year which also explains what to do for earlier terminated employees - Starting Single Touch Payroll Lodgments mid year
  • JocelynJocelyn Member Posts: 19
    edited April 2019

    Thank you!  That helps a bit. 
  • Sarah JohnstonSarah Johnston Member Posts: 38
    edited April 6
    HI Jocelyn,  I have had the same problem recently.  I was advised by Reckon to ring the ATO in regard to the errors.  The ATO had received all of my STP's even though the portal was advising error or pending, the ATO advised there was a glitch in the Reckon software and it was not working correctly.  I have been waiting on Reckon to fix the issue.  There is no need to lodge again, you can ring the ATO to double check they have all your STP's and more than likely it is a Reckon error.  Hope that helps :)
  • RavRav Administrator Posts: 10,925 Administrator
    edited June 2019
    Hi Sarah,
    I'm a little concerned at your comment.
    To make it clear, there are no issues with Reckon software and our transmission to the ATO for Single Touch Payroll pay events whatsoever.

    Error statuses relate to something specific and in most cases due to setup or something within the pay event file that is not in the correct format.
    Our STP team in particular would be extremely keen to follow up on this conversation with the ATO and what 'glitch' was being referenced by who you spoke with.
  • LeshelleLeshelle Member Posts: 90
    edited June 2019
    I have the same problem with two files in ERROR status. One is from yesterday, ie. the LAST pay run for the FY.
    The ATO have not got them according to the STP page in their Portal . Their is nothing specific in the error msg to fix and the ATO said to just lodge them again.  So perhaps there were technical issues at either the ATO or Reckon yesterday ? (26/6/19 around 4.30pm)
  • KimKim Member Posts: 4
    edited July 2019
    I've got the same problem and can;t get through to ATO
  • RavRav Administrator Posts: 10,925 Administrator
    edited July 2019
    Hi Leshelle and Kim,
    There has to be an error message response from the ATO that gives some indication as to what the error is (sometimes these can be a tad cryptic).
    Click on the 'Detail' link on the pay event and the response from the ATO will be at the top of the page inside the pay event itself.

    Let me know what the message is and I'll see if I can give you a bit more info.
  • LeshelleLeshelle Member Posts: 90
    edited July 2019
    Hi Kim and Rav My error messages were related to the ATO being unavailable. I tried re submitting my last pay event and it took awhile but eventually it went thru. That was last Thursday 27th.
  • KimKim Member Posts: 4
    edited July 2019

    Hi Rav

     

    The status initially says Pending but if you click on Pending you then het an error.

     

    If I click through the Error message I get the below.

     

    That said, I have taken the steps they outline, select Reckon and the software number specified but I still get the same result when I process the subsequent week.

     

    Thanks for the help and look forward to your advice

     

    Kim

     

     

    ATO Messages

    The following error messages have been returned from the ATO and need to be reviewed. You may need to make changed in your accounting product before submitting again.

    Error message

    • Your nomination with the software provider does not contain the correct Software ID in Access Manager.To resolve, please log on to Access Manager (AUSkey required), select 'my nominated software provider' and update the nomination, or call the ATO.You will need provide the following details:Software provider name and/or their ABN and Software ID

     

       
  • Peter GangellPeter Gangell Member Posts: 9
    edited August 2019
    Being a small business I have just started with STP from the 1st July. My 4 weekly payments have submitted ok but all have a status of pending. Who should I contact - ATO or Reckon?
  • RavRav Administrator Posts: 10,925 Administrator
    edited August 2019
    Hi Peter,
    Click on the 'Detail' link on the respective pay events to view the most recent response from the ATO.
    The status message in the list will also update based on that response ie. Success, Error etc.

    More info how the status messages work in GovConnect here -
    STP submission status messages in GovConnect
  • Kyle GrayKyle Gray Member Posts: 6
    edited August 2019

    Is there a way to create old stp files from recent pays?  I need to upload from last few weeks and it appears they are missing.
Sign In or Register to comment.