Assigning an Accounts Payable credit

JohnV
JohnV Member Posts: 6

I'm fairly new to Reckon and have not needed to use the Accounts Payable features before now. Normally we receive an invoice and pay it directly with "Write Cheque". In this instance I've been issued with a statement from a supplier that contains a number of invoices and credits. I've entered the invoices using Enter Bills then did the Credits in the same way. While saving each credit I was asked if I wanted to assign the credit against an outstanding invoice to which I said Yes, then when the 'where do you want to assign it' window appeared showing the available invoices, I cancelled. Now when I try to enter the payment for the balance of all the invoices and credits using "Pay Bill" I can only see the invoices on the list and the "Number of Credits" is "0". The creditor balance in Supplier Centre is the correct amount owing.

I presume I should have NOT cancelled that screen when entering the credits. How do I correct my mistake?

Thanks

Comments

  • Acctd4
    Acctd4 Accredited Partner Posts: 3,366 Reckon Accounts Hosted Expert Reckon Accounts Hosted Expert

    It sounds like you've already allocated the Credit automatically.

    If you want it to be available again - to apply in the Pay Bills window - go back in to the Bill Credit & change its value to $ 0, then re-save it - This will "unlink" it. Then open it again & edit it back to the correct credit amount & re-save. It will then be displayed as an available credit to allocate in Pay Bills

    Shaz Hughes Dip(Fin) ACQ NSW, MICB

    *** Reckon Accredited Partner (AP) Bookkeeper - specialising EXCLUSIVELY in Reckon Accounts / Hosted ! ***

    * Regd BAS Agent (No: 92314 015)* ICB-Certified Bookkeeper* Snr Seasonal Tax Consultant since 2003 *

    Accounted 4 Bookkeeping Services

    Ballajura, WA

    shaz@accounted4.com.au

    https://accounted4.com.au

    (NB: Please give my post a Like or mark as Accepted Answer if I have been able to resolve your query as this helps others when seeking solutions!)
  • JohnV
    JohnV Member Posts: 6

    Thanks for your reply. I think I've just made matters worse. As I've never used these features before, and based on your comment "It sounds like you've already allocated the Credit automatically", I decided to just proceed with the Pay Bill process. As stated previously, all that was shown was the two invoices (no credits), so I ticked them both and proceeded with "Pay Selected Bills". As you'd expect it generated a cheque for the value of the two invoice ($188.93) instead of the amount we actually paid ($46.31) being the value of the two invoices less the two credits. Can you please advise how I should go about fixing this?

    Thanks

  • Acctd4
    Acctd4 Accredited Partner Posts: 3,366 Reckon Accounts Hosted Expert Reckon Accounts Hosted Expert

    Delete the incorrect Bill Payment & go back in to Pay Bills. When you tick the bill, you should be able to see an amount in Total Credits Available (towards the bottom of the screen)

    With the applicable Bill ticked in the list, click on Set Credits to allocate (either all or partially) a credit amount to this Bill. This will then show in the Credits Used column, leaving the balance payable to match your payment.

    Shaz Hughes Dip(Fin) ACQ NSW, MICB

    *** Reckon Accredited Partner (AP) Bookkeeper - specialising EXCLUSIVELY in Reckon Accounts / Hosted ! ***

    * Regd BAS Agent (No: 92314 015)* ICB-Certified Bookkeeper* Snr Seasonal Tax Consultant since 2003 *

    Accounted 4 Bookkeeping Services

    Ballajura, WA

    shaz@accounted4.com.au

    https://accounted4.com.au

    (NB: Please give my post a Like or mark as Accepted Answer if I have been able to resolve your query as this helps others when seeking solutions!)
  • JohnV
    JohnV Member Posts: 6

    Thank you very much for your assistance. I believe it is right now.